The T132ECI integrated drive EC motor is the high-torque model of the T Series ECI line. It combines an IEC 132 frame permanent magnet synchronous motor (PMSM) with a variable frequency drive integrated inside the motor housing, removing the need for an external drive cabinet, shielded motor cable, or separate drive wiring. The representative variant delivers 35 N·m rated torque over a 100-900 rpm constant-torque range and 3.3 kW at 900 rpm, so large-diameter fans can be direct-driven without a gearbox or belt. It meets IE5 efficiency per IEC 60034-30-1, records 88.3% peak system efficiency at 900 rpm including drive losses, and runs from a 360-460 V, 50/60 Hz, three-phase supply.
Item | Value |
|---|---|
Power Range | 1.63-3.54 kW (IEC 132 frame) |
Rated Torque (Representative Variant) | 35 N·m |
Rated Power (Representative Variant) | 3.3 kW @ 900 rpm |
Input Power | 360-460 V, 50/60 Hz, Three-phase |
Speed Range | 100-900 rpm |
Efficiency | Up to 88.3% @ 900 rpm (system total efficiency, including drive losses) |
Energy Efficiency Class | IE5 (IEC 60034-30-1) |
Protection Class | IP55-IP66 |
Control Modes | Modbus RS485, 0-10 V, PWM |
Protection Functions | Overcurrent, rotor blockage, phase loss, IPM over-temperature, reverse wind startup |
Ambient Temperature | -25°C to +40°C |
Cooling Method | TEAO, minimum air speed 3 m/s |
Mounting | B3 standard; B5 / B14 optional; removable feet |
Shaft Extension | Diameter 38 mm |
Certification / Warranty | CE / ETL; 12 months (18 months overseas) |
The T132ECI delivers 35 N·m rated torque from 100 to 900 rpm, allowing a large-diameter axial or centrifugal impeller to mount directly on the shaft. This removes the gearbox or belt drive used in conventional fan trains and reduces the number of wear parts.
At 900 rpm the motor records 88.3% peak system total efficiency, measured at the rated point including drive losses. Low-speed, high-load duty is where AC induction motors show their lowest efficiency; the T132ECI is classified IE5 under IEC 60034-30-1 in this range.
With the drive built in, each motor needs one power and one control cable. It accepts 0-10 V, PWM, and Modbus RS485 control, and several motors can share one RS485 bus for group control of livestock house ventilation or cold storage air circulation.
The drive provides overcurrent, rotor blockage, phase loss, IPM over-temperature, and reverse wind startup protection. Rated S1 continuous duty with a brushless rotor, it supports unattended fan fleets with limited scheduled maintenance.
B3 foot mounting is standard; B5 and B14 flange mounting are optional and the feet are removable. Dimensions follow IEC standards, so an IEC 132 frame AC motor can be replaced in position without an adapter plate; the series supports all IEC mounting arrangements.
The shaft extension is 38 mm in diameter with an M12 threaded shaft end. The table lists the outline and mounting dimensions from the installation drawing. Each motor includes a 1.5 m power cable and a 1.5 m control cable; 2D and 3D drawings are available on request.
Dimension | Value |
|---|---|
Overall Length | 461 mm |
Frame Outer Diameter | Ø220 mm |
Shaft Extension to Hub Face | 70 mm |
Shaft Extension to Flange Face | 80 ±0.5 mm |
Flange Face to Front Foot Hole Center | 89 ±1.5 mm |
Foot Hole Spacing | 140 mm |
Rear Foot Hole Center to Rear Foot Edge | 12 mm |
Shaft Center Height | 132 mm |
Flange Mounting Hole Circle | 216 mm |
Flange Face Diameter | 260 mm |
The T132ECI uses TEAO cooling with a minimum 3 m/s air speed. IP55 protection is standard and upgradable to IP66, and the standard ambient range is -25°C to +40°C, with customized models available outside it.
The T132ECI is selected for high-torque, low-speed fan and pump duties: large livestock ventilation fans, cold storage fans, data center cooling, industrial fans, dust removal equipment, and water pumps. Its IEC-standard dimensions also support IEC 132 frame AC motor retrofits.
Voltage, speed, shaft diameter, mounting arrangement, control method, cable length, and connector type can be customized, with OEM manufacturing available. Bearing brands can be specified, and custom models are offered for ambient temperatures outside -25°C to +40°C.
Yes. The drive is integrated in the motor housing, so no external VFD, drive cabinet, or shielded cable is required.
The representative variant is rated 35 N·m over a 100-900 rpm constant-torque range, with 3.3 kW rated power at 900 rpm.
Yes. Its 35 N·m low-speed output supports direct coupling of large-diameter impellers, removing the gearbox or belt from the fan train.
It operates from a 360-460 V, 50/60 Hz, three-phase supply.
Yes. IEC-standard dimensions, B3 foot mounting, and B5/B14 flange options allow in-place replacement without an adapter plate.
It carries CE and ETL certifications. The warranty is 12 months from receipt domestically and 18 months from shipment for overseas orders.